VLAN Trunking Protocol

VLAN Trunking Protocol, aka VTP, is a Cisco proprietary protocol that allows Cisco switches to manage your VLAN database across all switches in your LAN through a central switch. This is done via a client / server environment.

A switch can operate in three VTP modes. The first is server mode. This is the VTP server which hosts the VLAN database and other switches on the LAN communicate to obtain a copy of the VTP database. In server mode, a network admin can add and remove VLANs at will.

The second is client mode. This is a VTP client. These switches communicate with the VTP server to obtain the database. A network admin can not add or remove VLANs manually from a switch in client mode.

And finally the the third mode is transparent mode. In transparent mode, the switch does not communicate with the VTP server and does not act as a VTP client. The network admin can add and remove VLANs from a switch in transparent mode and it will also allow VTP traffic to pass through it to other switches participating in the VTP domain.

Misconfigured, VTP can cause a major headache, but fortunately, troubleshooting VTP is pretty straight forward.

1. For VTP to propagate to switches in VTP client mode, they need to be connected as trunk ports. Switches connected together in access mode will not propagate any VTP changes.

2.The "Configuration Revision" number should be the highest on the server VTP switch. If the client has a higher revision number, then it will fail to obtain updates from the server. If a switch is introduced to the network that is running in VTP server mode, has the same VTP domain name as your server, and has the same password that you've setup in your VTP domain, then it will over-write your VLAN database throughout your network.

3. The "Configuration last modified" should list the IP Address of your VTP server switch. If it's not, then you have a rogue VTP server on your network.

accessswitch#sh vtp status
VTP Version : 2
Configuration Revision : 9
Maximum VLANs supported locally : 255
Number of existing VLANs : 8
VTP Operating Mode : Client
VTP Domain Name : rad
VTP Pruning Mode : Disabled
VTP V2 Mode : Enabled
VTP Traps Generation : Disabled
MD5 digest : 0x01 0x00 0xE6 0x40 0xE3 0x87 0x06 0x8C
Configuration last modified by 10.10.10.1 at 3-1-93 00:07:31

Fixing the issues are pretty straightforward, though may take a lot of manual input if you have a lot of VLANS.

1. If your client switches are not accepting updates from the server, verify that they are connected to the upstream switches via a trunking protocol. If that's correct, make sure that the "Configuration Revision" isn't higher than your VTP server. If it is, you can zero out the revision by changing to domain to null, changing the switch to server mode, then reconfiguring VTP in client mode.

2. If you have a rogue switch on the network that has taken over the role as VTP server, either remove the offending switch, or join it to the network in VTP client mode, then go to your VTP server and re-enter all your VLAN information in. You do have your VLAN information documented, right?

Other than that; use version 2, enable VTP pruning, use unique domain names, and use passwords on your VTP domain. If you're very paranoid, set all your switches to transparent mode and update the VLAN database on your switch infrastructure manually.

Commands Sets:

User EXEC mode:

show vtp counters
show vtp status
show vlan

Global Configuration mode:

CSW1(config)#vtp ?
domain Set the name of the VTP administrative domain.
file Configure IFS filesystem file where VTP configuration is stored.
interface Configure interface as the preferred source for the VTP IP updater
address.
mode Configure VTP device mode
password Set the password for the VTP administrative domain
pruning Set the adminstrative domain to permit pruning
version Set the adminstrative domain to VTP version
CSW1(config)#vlan ?
WORD ISL VLAN IDs 1-4094
access-map Create vlan access-map or enter vlan access-map command mode
dot1q dot1q parameters
filter Apply a VLAN Map
internal internal VLAN

VLAN Configuration mode:

CSW1(config-vlan)#?
VLAN configuration commands:
are Maximum number of All Route Explorer hops for this VLAN (or
zero if none specified)
backupcrf Backup CRF mode of the VLAN
bridge Bridging characteristics of the VLAN
exit Apply changes, bump revision number, and exit mode
media Media type of the VLAN
mtu VLAN Maximum Transmission Unit
name Ascii name of the VLAN
no Negate a command or set its defaults
parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs
private-vlan Configure a private VLAN
remote-span Configure as Remote SPAN VLAN
ring Ring number of FDDI or Token Ring type VLANs
said IEEE 802.10 SAID
shutdown Shutdown VLAN switching
state Operational state of the VLAN
ste Maximum number of Spanning Tree Explorer hops for this VLAN (or
zero if none specified)
stp Spanning tree characteristics of the VLAN
tb-vlan1 ID number of the first translational VLAN for this VLAN (or
zero if none)
tb-vlan2 ID number of the second translational VLAN for this VLAN (or
zero if none)